background
 

Search Products

 

Categories

Hot Stuff

 
Coolant Pipe Repair Kit for Vanagon

Here is some background info on the eventual failure of late model plastic coolant pipes on 1986-91 2WD & 4WD Vanagonsand our low cost, semi-permanent solution.



THE SITUATION:
The engine in all water-cooled Vanagons is in the rear and the radiator is up front. Running the length of the vehicle and underneath are two tubes through which the engine coolant is transferred to and from the radiator. At each end of these pipes are attached rubber hoses with hose clamps. These tubes are commonly referred to as “radiator coolant pipes.” On early water-cooled Vanagons (82-85) the pipes were made of 1-1/2 inch OD steel and painted black. On later model 1985-1/2 models, VW switched to 1-3/4 inch OD white plastic tubing with steel inserts at each end. In 1986 the entire cooling system changed, and the pipes were shortened in the rear, one by about 18 inches, the other by about 24 inches on 2WD models, and both about 24” shorter on 4WD models. They remained white plastic with steel inserts at each end. The system was unchanged through the end of the Vanagon production in 1991.

THE PROBLEM:
The problem with the steel pipes is that they would rust and fall apart. The plastic parts, of course, don't rust—which is great. But the problem with the plastic pipes is that over time the plastic barbs at each end would fail, and the metal inserts (also at each end) would work their way out into the hose (see photo above). This happens because the coefficient of friction between the plastic and the steel insert is very low compared to the friction between the plastic and the rubber hose. Heat, coolant flow, and vibration cause the metal insert to wiggle out of the plastic over time. Eventually, the metal insert wiggles out from under the spring clamp, allowing the plastic tubing to collapse. When this happens, the clamp can no longer exert any force between the hose and the plastic. So, the force generated by the coolant pressure exerted over the cross section of the hose (pressure x area) is no longer counteracted by the frictional force between the plastic and the rubber hose (clamping force x µ). In engineering terms, this is called a "free body diagram that is no longer in balance." In layman's terms it is called, "Holy crap, what is all that coolant doing on the ground!" Result: The hose blows off, which leads to all of the coolant rushing out, which in turn causes the engine to melt down and ruin an otherwise perfect roadtrip. 

The trick is keeping the metal inserts in place. Some people, including us, first thought that the way to go was simply to push the metal inserts back in, drill a little hole in the side, and use a fastener to keep the metal insert in place. In fact, that is how we fixed a set on one of our personal Vanagons back in 1996. What happened over time was this: the hole we drilled caused the pipe to crack, and then we were completely screwed—and eventually had to replace the pipes with a set of new stainless steel ones. That is the ultimate solution: switch to stainless steel pipes. They can't rust or fall apart. HOWEVER, this is a somewhat costly fix, and it might not be necessary.

THE SOLUTION:
If your plastic pipes are still otherwise serviceable (not cracked or otherwise damaged), the GoWesty kit can breath relatively inexpensive new life into them. The kit consists of a set of custom-made brass fittings of the appropriate size and shape. These fittings are placed inside the hose and clamped down securely. Then, the hose is installed on the plastic pipe and secured by a separate clamp (see cross-section photos below). Now the frictional force between the plastic pipe and the rubber hose acts to hold the whole thing together indefinitely because the steel insert can't wiggle out of place. How do we know this works? WE have installed this kit in our shop for almost 10 years now. Many of these vehicles come back for service work, and we can see with our own eyes that the hoses are in place and nothing has moved. Plus, we have sold hundreds of these kits online. If this solution did not work, we probably would have heard about it by now... Every Westy we sell has one of these kits installed or a new set of stainless steel pipes. 



2WD KIT CONTENTS:
(3) STAINLESS STEEL SCREW CLAMP
(5) OEM GREEN SPRING CLAMP
(2) 1-1/2” FLARED TO 1-3/4” BRASS FITTING, STRAIGHT
(1) 1-1/2” BRASS FITTING, WITH BEND
(1) 1-3/4” BRASS FITTING, STRAIGHT
(1) INSTRUCTIONS AND PHOTOS

SYNCRO KIT CONTENTS:
(4) STAINLESS STEEL SCREW CLAMP
(4) OEM GREEN SPRING CLAMP
(4) 1-1/2” FLARED TO 1-3/4” BRASS FITTING, STRAIGHT
(1) INSTRUCTIONS AND PHOTOS



INSTALLATION INSTRUCTIONS:
Drain cooling system. Remove hoses from both ends of both pipes and discard existing screw clamps. If the metal inserts have worked their way out, heat the plastic with a heat gun or powerful hair dryer and tap them back in flush with the end of the plastic tubing. If the plastic tubing has split apart leaving a plastic ring, remove it and discard it too. Insert the appropriate brass fitting supplied in the kit into the rubber hose. On 2WD’s, both front hoses get the exact same fitting, the two rear each get different ones, refer to the photos. On 4WD’s all four ends are the same. The idea is that when the hose is installed on the plastic pipe fully, the end of the metal insert butts up against the newly installed brass fitting inside the hose. Install the brass fitting into the hose such that it allows enough exposed hose for full engagement onto the plastic pipe. On the two front fittings and the one rear fitting with the bend, just install the brass fitting until it bottoms on the flare of the hose. On 4WD models, all four ends are done this way. Secure the fittings in the hose with one of the three supplied SCREW clamps. On the rear fitting that has a simple straight hose (no flare, 2WD only), just install the fitting about 1-1/2" in from the end. Secure the brass fitting in the hose with one of the five supplied GREEN SPRING clamps provided. Now install the hose onto the plastic pipe end and secure with the remaining four GREEN SPRING clamps provided. That’s it! Run it! On to the next problem!


Back to Library



Additional Photos

GoWesty! Camper Products is a privately owned company specializing in parts, accessories, sales and service of Volkswagen (R) campers. It is not affiliated in any way with Volkswagen of America or Volkswagen AG. "Vanagon", "Bus", "VW", "Volkswagen", and "Eurovan" are registered trademarks and should be considered as such throughout our entire website.

 

Featured Vehicle

Featured Vehicle For Sale More Details
Our Price: $59,363.47
 
 
Calendar Contest
 
Core Buyback
 
Recycle Bin
 
International Distributors
 
VWCP
 
Made in the USA
 
UPS Carbon Nuetral